Thread cutting

Set of 4 quick-release bits / bushings / inserts / collets TC820 for machine taps The set contains the following bits for taps made according to DIN371: 1x M5(clamps also M6) 1x M6(clamps also M5) 1x M8 1x M10 Inserts can also be purchased separately - see related products. How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The tap is clamped in a suitable collet TC820, which has a torque clutch already preset, or it is possible fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.

M3 - M12 Clamping shank: Straight ISO40 < br> Standard: DIN69871 Clamping kit sets: DIN 371 (reinforced shank): M3; M4; M4.5; M5; M6; M7; M8; M10 DIN 376 (classical shank): M4,5; M5; M6; M8; M12 Length compensation - see photo no.3, no.4 and no.12 The set is delivered in the trunk - see photo 9 and no.10 Taper clamping method: The taps are secured in the extension behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo no.5 and no.6 Expansion of the attachment see photo no.7 and no.8 You can buy the set Taps for M1 - M16 taps - see photo n ° 11 Taps for taps manufactured according to JIS and ISO 529 standards, which are not common in our country, are also available for tapping heads. About 90% of the domestic market consists of taps made to DIN standards Taps are not a part of the set! The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

norms: DIN69871 Adapters in set of taps: DIN 371 (reinforced stopper): M8; M10; DIN 376 (classical shank): M12; M14; M16; M18; M20 Length compensation - see photo no.3, no.4 and no.12 The set is delivered in the trunk - see photo 9 and no.10 Taper clamping method: The taps are secured in the extension behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo no.5 and no.6 Extension of the extension see photo no.7 and no.8 You can buy the set Taps for M5 - M24 taps - see photo n ° 11 Taps for taps manufactured in accordance with JIS and ISO 529, which are not common in our country, can also be purchased for the die head. Approximately 90% of the domestic market consists of taps made according to DIN standards Taps are not a part of the set!

Quick-release threading head with length compensation for TC 1433 attachments with torque coupling for machine taps Clamp range: M14 - M33 Clamp shank: steep taper BT ISO50 Length from spindle: Standard: JIS 6339 MAS ??BT 50 Length compensation - see photo (other photos are for type DIN69871) Method of clamping the tap: The taps are in the extension secured by a square and a clamping shank. The tap is firmly held in the extension, it is pulled out after pressing the clamping collar in the front of the extension. The extensions are secured in the head via the bearing and stones - see photo (photo is for type DIN69871) Ejection of the extension - see photo (other photos are for type DIN69871) < u>Extensions and taps are not part of the set! Functions: The tap is clamped in a suitable collet TC1433, which has a torque coupling already preset. or it is possible to fine-tune it as needed. The thread cutter has a length compensation of approx. 0.5 cm, so it is enough to program the appropriate cutting depth. The torque coupling prevents the tap from twisting.

Quick-action tapping head with length compensation for TC 1433 attachments with torque coupling for machine taps Clamping range: M14 - M33 Clamping shank: steep taper DIN ISO50 Length from spindle: Standard: DIN69871 50 Length compensation - see photo Method of clamping the tap: The taps are secured in the extension by a square and a clamping shank. The tap is firmly held in the extension, it is pulled out after pressing the clamping collar in the front of the extension. The attachments are secured in the head via the bearing and stones - see photo Extension of the attachment - see photo The attachments and taps are not part of the set! Function: The tap is clamped in a suitable collet TC1433, which has a torque coupling already preset, or it can be fine-tuned as needed. The thread cutter has a length compensation of approx. 0.5 cm, so it is enough to program the appropriate cutting depth. The torque coupling prevents the tap from twisting.

Air Tapping / Thread Cutting Range: M8-M16 Speed: 230-250 rpm For Taps Adapters - Type: TC-820 Clamping Head Diameter into the sleeve of the arm: 61,3mm Thread cutting without adapter for taps - see related products Order no. No. 3404-434

Reducing insert for tapping machine with collets TC-820, after its use it is possible to clamp smaller collets TC-312 - see related products.

Reducing insert for thread cutter with collets TC-1433, after using which it is possible to clamp smaller collets TC-820 - see related products.

DIN 371 (reinforced shank) : M5 and also M6 DIN 376 (classic shank): M8 Thread clamping method: Taps they are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.

DIN 371 (reinforced shank) : M6, and also M5 DIN 376 (classic shank): M8 Thread clamping method: Taps they are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.

DIN 371 (reinforced shank) : M8 DIN 376 (classic shank): Length compensation - see enclosed photo Tapping method: Taps are in the attachments are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.

DIN 371 (Reinforced Shank) : M10 DIN 376 (classic shank): Length compensation - see enclosed photo Tapping method: Taps are in the attachments are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.