Thread cutting

Clamping Shank: Diameter 32mm, with Welding Plate Clamping Taps: M3 - M25 Fuse for Internal Quadrant - see attached photo. Collars: ER32 Length from spindle: 90mm Clamping lenght: 100mm

Clamping Shank: Dia. 20mm, with Welding Plate Clamping Taps: M3 - M10 Fuse for Internal Quadrant - see attached photo. Collet: ER16 Length from spindle: 47mm Clamping lenght: 80mm

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: internal cone B16 - Ideal for drills that have a fixed outlet B16, ie a 16mm outer cone that is not Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Quick-release tapping head for TC 820 attachments for machine taps according to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque coupling is adjusted directly on the collet. Clamping range of the thread cutter: M5 - M20 ( need to purchase TC820 collets ) Clamping shank: inner cone B16 - Ideal for drills that have a fixed outlet B16, i.e. 16mm outer cone, which cannot be replaced Alternatively, it can be clamped on ordinary drill mandrels with an external cone B16 - see attached photos Total length: 80mm Method of clamping the tap: The taps are clamped in TC820 collets, which need to be purchased separately. The taps are secured in the collet by the square and the clamping shank. The tap is held firmly in the collet, pulled out after pressing the clamping collar. The collets are secured in the head via the bearing and stones. To the threading head, it is also possible to purchase attachments for taps made according to JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps made according to DIN371,374,376 standards Clamping collets TC820 are not part of the tap - they need to be purchased separately! Function: The tap is clamped in a suitable collet TC820, which has a torque coupling already preset, or it can be fine-tuned as needed.

Quick-release tapping head for TC 820 attachments for machine taps according to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque coupling is adjusted directly on the collet. Clamping range of the thread cutter: M5 - M20 ( need to purchase TC820 collets ) Clamping shank: inner cone B18 - Ideal for drills that have a fixed outlet B18, i.e. 16mm outer cone, which cannot be replaced Alternatively, it can be clamped on ordinary drill mandrels with an external cone B18 - see attached photos Total length: 80mm Method of clamping the tap: The taps are clamped in TC820 collets, which need to be purchased separately. The taps are secured in the collet by the square and the clamping shank. The tap is held firmly in the collet, pulled out after pressing the clamping collar. The collets are secured in the head via the bearing and stones. To the threading head, it is also possible to purchase attachments for taps made according to JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps made according to DIN371,374,376 standards Clamping collets TC820 are not part of the tap - they need to be purchased separately! Function: The tap is clamped in a suitable collet TC820, which has a torque coupling already preset, or it can be fine-tuned as needed.

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: 32mm, cylindrical Clamping length: 70mm Clamping method: < / b> The taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Adjustable Key for TC-312 and TC-820 Inserts Range: 7-40 mm Key Diameter Keys: 3,0mm For TC-312 Collet Pins Needed mildly good - inaccuracy from production. For TC-820, use is easy. Ref. : 3404-150

Socket wrench for inserts TC-312 Diameter of key pins: 2.6mm Pin spacing: 24mm Total length of key: 120mm

Socket wrench for TC-820 inserts Diameter of key pins: 2.9mm Pin spacing: 38mm Total length of key: 135mm

Adjustable Key for TC1433 Inserts Range: 11-60 mm Key Diameter Keys: 4mm Ref.No. : 3404-151

Set of 8 quick-release bits / bushings / inserts / collets TC312 for machine taps The set contains the following bits for taps made according to DIN371: 1x M1(upne also M1,1 to M1,8) 1x M2(upne also M2,2 to M2,5) 1x M3 1x M3,5 1x M4 1x M5(upne also M4,5 and M6) 1x M8 1x M10 Inserts can also be purchased separately - see related products . How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The screw is clamped in a suitable collet TC312, which has a torque coupling already preset, or it is possible more fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.

Set of 8 quick-release bits / bushings / inserts / collets TC820 for machine taps The set contains the following bits for taps made according to DIN371: 1x M8 1x M10 1x M12 1x M14 1x M16 1x M18 1x M20 1x M22(upne also M24) < br> Inserts can also be purchased separately - see related products. How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The tap is clamped in a suitable collet TC820, which has a torque clutch already preset, or it is possible fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.