KOPAL (Francie)

Run for 60 Â ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Shrinkage angle: 60 ° Podbrus blade: 14 Â ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 88x20 x 8.7mm Cat. A „. : 02-315

Run for 60 Â ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Shrinkage angle: 60 ° Podbrus blade: 0 Â ° Material: HSS Coating: uncoated Application: suitable for brass, bronze, cast iron, heat-resistant steel You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 88x20 x 8.7mm Cat. A „. : 02-317

Run for 60 ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Shrinkage angle: 60 ° Podbrus blade: 20 ° Material: HSS Coating: uncoated Usage: suitable for Stainless steel, swords, plastics, stainless steel You can compare the differences in the undercut table in the attached photos. Knife dimensions: 88x20 x 8,7mm Cat. Ä. : 02-318

Run for 60 Â ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Shrinkage angle: 60 ° Podbrus blade: 25 Â ° Material: HSS Coating: uncoated , Iron, sheets You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 88x20 x 8.7mm Cat. A „. : 02-319

Pipe machine / machine needle, needles on the outside and inside of the pipe at the same time Range for internal needling: 12-24mm Range for external needling: 14-24mm Bevel angle: 90 Â ° Number of holes: 1x outer and 1x inner(run) is rotatable - ie for two uses) Clamping shank: cylindrical 12.7 mm Speed: 10- 20 m / min. The heart is delivered without running , these can be purchased with a sharp angle: a) 14 Â °(cat. No. 04-300 04-310), suitable for special bronze, plexiglass b) 20 Â °(cat. No. 04-303 04-313), suitable for common steel, gauge, plastic, stainless steel Dimensions of the needle: Total length: 140mm Diameter Housing outer / inner: 45 / 38mm Clamping shank length: 50mm Blade insertion procedure and adjustment of bevel / chamfer height 1) Loosen the worms on the cover case 2) Loosen the worms on the body of the needle(2pcs on one side, 3pcs on the other side) 3) Insert the body into the body, secure it with two worms. 4) There are two heads in the package - depending on which head you choose, the chamfer will be larger on the inside(concave shape of the head) or on the outside(convex shape heads) tubes. 5) You always set the height of the chamfer only on the side where 3 worms are used to secure the knife. 6) Make sure that the run is not drowned in the body of the needle, if so, adjust the run so that the run is stuck out(applies to the side where is already protected by three worms).

Punching machine for pipes / machine needler, needles the outer and inner side of the pipe at the same time Range for internal needling: 20-30mm Range for external needling: 24-36mm < br> Bevel angle: 90 Â ° Â ° Number of holes: 1x outer and 1x inner(run) is rotatable - ie for two uses) Clamping shank: morse 2 / MK2 Speed: 10-20 m / min. The heart is delivered without running , these can be purchased with a sharp angle: a) 14°(cat. No. 04-320 + 04-330), suitable for special bronze, plexiglass b) 20° (cat. No. 04-323 + 04-333), suitable for common steel, meter, plastic, stainless steel Dimensions of the needle: Total length: 190mm Diameter Housing outer / inner: 60 / 48mm Clamping shank length: 80mm How to insert the blade and adjust the height of the bevel / chamfer 1) Loosen the worms on the cover case 2) Loosen the worms on the body of the needle(2pcs on one side, 3pcs on the other side) 3) Insert the body into the body, secure it with two worms. 4) There are two heads in the package - depending on which head you choose, the chamfer will be larger on the inside(concave shape of the head) or on the outside(convex shape heads) tubes. 5) You always set the height of the chamfer only on the side where 3 worms are used to secure the knife. 6) Make sure that the run is not drowned in the body of the needle, if so, adjust the run so that the run is stuck out(applies to the side where is already protected by three worms).

Internal run for machine needle 04-060 brand KOPAL. Bevel angle: 90 ° Podbrus blade: 14 Â ° Material: HSS Coating: uncoated Fitting position: for internal needle tubes Usage : suitable for special bronze, plexiglass You can compare the differences in the sharpening of the underlay on the attached photos. Contact the Company: Cat. A „. : 04-300

Internal run for machine needle 04-060 brand KOPAL. Bevel angle: 90 ° Podbrus blade: 20 Â ° Material: HSS Coating: uncoated Fitting position: for internal needle tubes Usage : suitable for ordinary steel, sword, plastics, stainless steel You can compare the differences in the sharpening of the underlay on the attached photos ch. Contact the Company: Cat. A „. : 04-303

External run for machine needle 04-060 brand KOPAL. Bevel angle: 90 ° Podbrus blade: 14 Â ° Material: HSS Coating: uncoated Fitting position: for exterior needling tubes Usage : suitable for special bronze, plexiglass You can compare the differences in the sharpening of the underlay on the attached photos. Contact the Company: Cat. A „. : 04-310

External run for machine needle 04-060 brand KOPAL. Shrinkage angle: 90 ° Podbrus blade: 20 Â ° Material: HSS Coating: uncoated Installation location: for external needling tubes Usage : suitable for ordinary steel, sword, plastics, stainless steel You can compare the differences in the undercut table photos. Contact the Company: Cat. A „. : 04-313

Internal run for machine needle 04-090 brand KOPAL. Bevel angle: 90 ° Podbrus blade: 14 Â ° Material: HSS Coating: uncoated Fitting position: for internal needle tubes Usage : suitable for special bronze, plexiglass You can compare the differences in the sharpening of the underlay on the attached photos. Contact the Company: Cat. A „. : 04-320

Internal run for machine needle 04-090 brand KOPAL. Bevel angle: 90 ° Podbrus blade: 20 Â ° Material: HSS Coating: uncoated Fitting position: for internal needle tubes Usage : suitable for ordinary steel, sword, plastics, stainless steel You can compare the differences in the sharpening of the underlay on the attached photos ch. Contact the Company: Cat. A „. : 04-323