KOPAL (Francie)

Machine chisel for external edges / machine needle Range: 10-45mm Bevel angle: 90° Number of slots for edge inserts : 2 < br> Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for outer edges / machine needle Range: 10-45mm Bevel angle: 90° Number of slots for edge inserts : 2 < br> Clamping shank: cylindrical dia. 16mm and dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a) 0 Â °(cat. No. 02-312), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special Bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel and d) 20 Â ° TiN(cat. No. No. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. No. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Overall length: XXmm Diameter of the front part: XXmm Diameter aluminum nut dimensions: XXmm and XXmm Clamping shank length: XXmm Blade insertion procedure and edge / chamfer height adjustment 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for outer edges / machine needle Range: 10-45mm Bevel angle: 60° Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-317), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1 ) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for outer edges / machine needle Range: 10-45mm Bevel angle: 60° Number of slots for edge inserts : 2 Clamping shank: cylindrical dia. 16mm and dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a) 0 Â °(cat. No. 02-317), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special Bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel and d) 20 Â ° TiN(cat. No. No. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. No. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Overall length: XXmm Diameter of the front part: XXmm Diameter aluminum nut dimensions: XXmm and XXmm Clamping shank length: XXmm Blade insertion procedure and edge / chamfer height adjustment 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for external edges / machine needle Range: 21-57mm Bevel angle: 90° Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for outer edges / machine needle Range: 21-57mm Bevel angle: 60° Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) n without bend , these can be purchased with a sharp angle: a ) 0 Â °(cat. no. 02-317), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1 ) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for external edges / machine needle Range: 41-77mm Bevel angle: 90° Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for external edges / machine needle Range: 41-77mm Bevel angle: 90° Number of slots for edge inserts : 2 Clamping shank: MK3(morse 3) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for outer edges / machine needle Range: 41-77mm Bevel angle: 60° Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-317), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1 ) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for outer edges / machine needle Range: 41-77mm Bevel angle: 60° Number of slots for edge inserts : 2 < br> Clamping shank: MK3(morse 3) n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-317), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1 ) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for external edges / machine needle Range: 60-97mm Bevel angle: 90 Number of slots for edge inserts : 2 Clamping shank: MK3(morse 3) n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for external edges / machine needle Range: 80-117mm Bevel angle: 90° Number of slots for edge inserts : 2 Clamping shank: MK3(morse 3) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needles / chamfers Edges 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.