Turning

External replaceable blade thread insert 11 EL W Size: 11 Number of strokes per inch: according to the selected variant Full profile / partial profile: depending on the selected variant Apex angle: 55° Design of the plate: left Height (to edge): 3.2mm Suitable for cutting an external inch whitworth thread W (category BSW,BSF,BSP,BSB) Coating: PVD TiALN Blade material: BMA - universal use, suitable for classic and stainless steel, non-traditional materials, for normal to high cutting speeds Usage : Steel: P20-P40 Stainless steel Cast iron: K20-K30 Refractory steel (Ni,Co,Fe,Ti) Hardened steel For cutting conditions, see the attached catalog, page no. 56 (sheet no. 60). Cat. No. : The price shown is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Internal replaceable cutting edge thread insert 11 IR W Size: 11 Number of strokes per inch: according to the selected variant Full profile / partial profile: depending on the selected variant Apex angle: 55° Design of the plate: right Height (to edge): 3.2mm Suitable for cutting internal inch whitworth thread W (category BSW,BSF,BSP,BSB) Coating: PVD TiALN Blade material: BMA - universal use, suitable for classic and stainless steel, non-traditional materials, for normal to high cutting speeds Usage : Steel: P20-P40 Stainless steel Cast iron: K20-K30 Refractory steel (Ni,Co,Fe,Ti) Hardened steel For cutting conditions, see the attached catalog, page no. 56 (sheet no. 60). Cat. No. : The price shown is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Turning knife left with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223713 / CSN 22 3713, DIN4972, DIN4972L, ISO2 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Turning knife left with soldered blade Square: according to the selected variant Overall length: see product description for selected variant Carbide: according to the selected variant Carbide marking: P - steel K - cast iron U - stainless steel, heat-resistant alloys Carbide numbering: 05 - finishing - extra hard / brittle carbide, uninterrupted cut, very good final surface 10 - finishing - hard / brittle carbide, uninterrupted cut, very good final surface 20 - semi-roughing - clean turning 30 - roughing, interrupted cut 45 - extra roughing, intermittent cutting, withstands poorer handling, turning under difficult conditions Use: according to the selected variant Standard: ČSN 223713 / CSN 22 3713, DIN4972, DIN4972L, ISO2 Attention - these soldered knives are semi-finished products - before starting machining it is necessary to grind a suitable breaker. If you have nowhere to sharpen these knives, we recommend switching to holders with replaceable carbide inserts.

Fixed lathe tip with 60 ° apex angle and sintered carbide insert Morse taper size: according to the selected variant Other dimensions - see labels for individual variants The whole tip is hardened to a hardness of HRC 58 to 62. Standard: ČSN 243311 / ČSN 24 3311 / DIN806 / DIN 806

Quick-change round knife holder for multi-fix Size: according to the chosen variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Quick-change parting knife holder for multi-fix Size: according to the chosen variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Morse swivel tip for clamping heavy workpieces Morse taper: according to the selected variant Other dimensions and parameters - see description for individual variants Top angle: 60 ° Standard: ČSN 24 3325 Type N: Throw 0.04mm Type E: Throw 0.01mm

Morse swivel tip for clamping heavy workpieces Morse taper: according to the selected variant Other dimensions and parameters - see description for individual variants Top angle: 90 ° Standard: ČSN 24 3325 Type N: Throw 0.04mm Type E: Throw 0.01mm

Quick-change holder for Morse clamping sleeves for multi-fix Size (diameter x length): according to the selected variant Suitable for head / multifix: according to the selected variant Other dimensions - see attached catalog sheet

Right holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Angle of the plate to the axis: 95° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.

Right holder for exchangeable slices, fastening with a screw Knife for internal turning Clamping diameter: according to the selected variant Marking of plates that fit into the holder: according to the selected variant (CCMT or CCGT) Angle of the plate to the axis: 93° Other dimensions - see product description for individual variants The product comes with a key for changing the blade. The plate is not part of the package, it can be purchased separately - see related products. General information on choosing a suitable holder: Type "S" holders - with screw clamping are suitable for normal to finishing operations. They are suitable for smaller removals of material. The inserts for these holders have a positive back of the insert, which enables a sharper geometry of the inserts and thus the possibility of achieving a better surface quality. P, "M" , "T" , "C" and "D" type holders with thumb or clamp are suitable for normal to roughing operations - they have higher rigidity. The inserts for these holders have a negative (straight) back of the insert, thanks to which the inserts do not break / deform so much and it is possible to rough with them and to machine better / longer even harder-to-machine materials.