Metal drills, cylinder. stalk

Carbide drill for drilling bent taps For tap: M5 d1(H7): 4,20 mm Max. depth l3: 19mm Total length l1: 50mm Clamping shank: cylindrical 5-edge Helix angle: 0A ‚ ° Use up to 65 HRC Speed â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0030

Carbide drill for drilling bent taps For tap: M6 d1(H7): 5,00 mm Max. depth l3: 23mm Total length l1: 50mm Clamping shank: cylindrical hexagon Helix angle: 0Â ° Use up to 65 HRC Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0040

Carbide drill for drilling bent taps For tap: M8 d1(H7): 6.80 mm Max. depth l3: 23mm Total length l1: 60mm Clamping shank: cylindrical 8 edges Helix angle: 0A ‚ ° Use up to 65 HRC> Speed ??â €‹ â € ‹(for range M3-M12): 1000-1500 rpm rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0050

Carbide drill for drilling bent taps For tap: M10 d1(H7): 8.50 mm Max. depth l3: 25mm Total length l1: 80mm Clamping shank: cylindrical 10 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0060

Carbide drill for drilling bent taps For tap: M12 d1(H7): 10,20 mm Max. depth l3: 35mm Total length l1: 80mm Clamping shank: cylindrical 12 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0070

Carbide drill set for drilling bent taps For taps: M3 - M4 - M5 - M6 - M8 - M10 - M12 d1(H7): 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm Max. depth l3: 10/14/19/23/23/25/35 mm Total length l1: 38/46/50/50/60/80/80 mm Clamping shank: cylindrical Hexagon < br> Helix angle: 0  ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1865

Extended black right-handed steel twist drill with cylindrical shank Diameter: 10.2mm Drill length: Extended width Series - lengths see attached photo( same length as for DIN340 drills) Drilling depth: 10xD cutting angle: 118 ° C > Helix angle: 25 ° to 30 ° Material: HSS - High speed steel Standard: ÄOSN 221125, black extension drills Usage: General - hand, stand, column drills Non-alloy steel, cast steel with strength up to 600 N / mm2

Cross section of regular trapezoid Cutting Edge Width: 2mm Height: 8mm Length: 80mm Material: HSS - High-Speed ??Steel ČSN 22 3693

Set of 5 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 4 / 5 / 6 / 8 / 10 mm Drill length: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly also hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283054005

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 19 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-10.0mm x 0.5mm Length of the drill: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly even hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057019

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 24 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-10.5mm x 0.5mm drill bits 3.3 / 4.2 / 6.8 / 10.2 mm Drill length: Short series - lengths see attached photo Material: HSSE - High speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly also hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057024

The photo is illustrative - new - we will take a photo immediately after stocking. Set of 25 pcs - 3-edged right-cut ground spiral cobalt drill bits for steel and stainless steel with cylindrical shank Set contains diameters: 1.0-13.0mm x 0.5mm Length of the drill: Short series - lengths see attached photo Material: HSSE - High-speed steel Co5 / HSSCo5 Standard: DIN338 ( replaces PN 2907 / PN2907 ) Usage: Stand and column drills, NC and CNC machines, possibly even hand drills. Structural steel Unalloyed and alloyed steel, cast steel with strength up to 850N/mm2 Stainless steel Wrought aluminum alloys and other aluminum alloys Advantages: Higher geometry / hole ovality - depending on the machine used, accuracy up to IT9 can be achieved. Thanks to three blades, the feed can be increased by up to 60%. The special geometry of the tip of the drill prevents the drill from slipping. Thanks to this, there is no need to use a punch to center the holes. The drill does not jam when re-drilling an existing hole. The chip is removed without a problem, less wear on the drill bit / longer service life, thanks to the distribution of the engagement on 3 blades. Cat. no.: 283057025