Iscar

Grooving insert, replaceable insert for turning - grooving DGN1500P IC508 , Iscar Recess width: 1.5mm Coating: PVD , TiCN TiN IC508 series: Tough submicron substrate with TiCN TiN PVD coating. Designed for a wide range of materials at low to medium cutting speeds, intermittent cutting and unstable conditions. Highly resistant to notch wear and build-up. Usage: Steel: P20-P40 Stainless steel: M20-M30 Cast iron: K20-K30 Non-ferrous metals and plastics: N10-N30 Superalloys: S10- S40 Carbide: H10-H20 Cutting conditions - see attached photo Type P: Dividing and grooving of soft (sticky) materials, thin and small workpieces. Very sharp breaker geometry - similar to a polished blade. Order no. no.: 6002938 The price shown is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Turning insert, Turntable cutting insert DGN1002J IC908, Iscar Cutting width: 1,0mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Application: Steel: P15-P30 Stainless Steel: M20-M30 Cast Iron: K20-K40 Non Ferrous Metals & Plastics: N05-N20 S05- S20 Hardened H05-H15 Ref. No .: 6002945

Parting insert, replaceable insert for turning - parting DGN5003C IC908, Iscar Cutting width: 5.0mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrates TiAlN PVD coated. Suitable for low to medium cutting speeds. Developed for machining heat-resistant alloys, austenitic stainless steels and very hard steels. High resistance to chipping, oxidation. Suitable for a wide range of materials and packaging conditions. Application: Steel: P10-P30(Vc = 70-180 m / min; 230-590sfm; Fn = 0.04-0.12 mm / rev) Stainless steel: M05-M20(Vc = 50-180 m / min; 160-590 sfm; Fn = 0.04-0.12 mm / rev) Cast iron: K15-K30(Vc = 110-175m / min; 360-570 sfm; Fn = 0.04-0.12 mm / rev) Non-ferrous metals and plastics: N05-N20 Superalloys: S05-S20 Carbides: H05-H15 A Cutting conditions - see attached photo Type C: For parting and grooving bars, hard materials. Ord. Ä. 6002946 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Turning insert, Turntable cutting insert DGN1402J IC908, Iscar Cutting width: 1,4mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Application: Steel: P15-P30 (Vc = 70-180 m / min; 230-590sfm) Stainless steel: M20-M30 (Vc = 50-180 m / 590 sfm) Cast iron: K20-K40 (Vc = 110-175m / min; 360-570 sfm) Non-ferrous metals and plastics: N05-N20 S05-S20 - -H15 Ref. No.: 6002957

Turning insert, Turntable cutting insert DGN1502J IC908, Iscar Cutting width: 1,5mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Application: Steel: P15-P30 Stainless Steel: M20-M30 Cast Iron: K20-K40 Non Ferrous Metals & Plastics: N05-N20 S05- S20 Hardened H05-H15 Ref. No .: 6002958

Turning insert, Turntable cutting insert - DGN2002C IC908, Iscar Cutting width: 2,0mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Usage: Steel: P10-P30 (Vc = 70-180 m / min; 230-590sfm; Fn = 0,04-0,12 mm / rev.) Stainless steel: M05 -M20 (Vc = 50-180 m / min; 160-590 µm; Fn = 0.04-0.12 mm / rev.) Cast iron: K15-K30 (Vc = 110-175m / 570 sfm; Fn = 0,04-0,12 mm / rev.) Non-Ferrous Metals and Plastics: N05-N20 Superslitz: S05-S20 Hardened: H05-H15 Typical conditions - see enclosed photo Type C: For cutting and grooving bars, hard materials. Ref. No. 6002959

Turning insert, Turntable cutting insert - DGN2202C IC908, Iscar Cutting width: 2,2mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Usage: Steel: P10-P30 (Vc = 70-180 m / min; 230-590sfm; Fn = 0,04-0,12 mm / rev.) Stainless steel: M05 -M20 (Vc = 50-180 m / min; 160-590 µm; Fn = 0.04-0.12 mm / rev.) Cast iron: K15-K30 (Vc = 110-175m / 570 sfm; Fn = 0,04-0,12 mm / rev.) Non-Ferrous Metals and Plastics: N05-N20 Superslitz: S05-S20 Hardened: H05-H15 Typical conditions - see enclosed photo Type C: For cutting and grooving bars, hard materials. Ref. No. 6002960

Turning insert, Turntable cutting insert DGN2202J IC908, Iscar Cutting width: 2,2mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Usage: Steel: P10-P30 (Vc = 70-180 m / min; 230-590sfm; Fn = 0,04-0,12 mm / rev.) Stainless steel: M05 -M20 (Vc = 50-180 m / min; 160-590 µm; Fn = 0.04-0.12 mm / rev.) Cast iron: K15-K30 (Vc = 110-175m / 570 sfm; Fn = 0,04-0,12 mm / rev.) Non-Ferrous Metals and Plastics: N05-N20 Superslitz: S05-S20 Hardened: H05-H15 Tough conditions - see enclosed photo Type J: For cutting and grooving pipes, smaller diameters and thin-walled materials Ref. No. 6002961

Parting insert, replaceable insert for turning - parting DGN4003C IC908, Iscar Cutting width: 4,0mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrates with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining heat-resistant alloys, austenitic stainless steels and very hard steels. High resistance to chipping, oxidation. Suitable for a wide range of materials and packaging conditions. Application: Steel: P10-P30(Vc = 70-180 m / min; 230-590sfm; Fn = 0.04-0.12 mm / rev) Stainless steel: M05-M20(Vc = 50-180 m / min; 160-590 sfm; Fn = 0.04-0.12 mm / rev) Cast iron: K15-K30(Vc = 110-175m / min; 360-570 sfm; Fn = 0.04-0.12 mm / rev) Non-ferrous metals and plastics: N05-N20 Superalloys: S05-S20 Carbides: H05-H15 A Cutting conditions - see attached photo Type C: For parting and grooving bars, hard materials. Ord. Ä. 6002964 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Turning insert, Turntable cutting insert - DGN2202J IC1028, Iscar Cutting width: 2,2mm Coating: PVD, TiAlN TiN < IC1028 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. Usage: Steel: P20-P50 (Vc = 60-170 m / min; 200-560sfm; Fn = 0,04-0,12 mm / rev.) Stainless steel: M20 -M40 (Vc = 60-150 m / min; 200-490 fm; Fn = 0.04-0.12 mm / rev.) Conditions of use - see enclosed photo Type J: For cutting and grooving pipes, smaller diameters and thin-walled materials Ref. No .: 6003041

Turning insert, Turntable cutting insert DGN2202J IC908, Iscar Cutting width: 2,2mm Coating: PVD, TiAlN IC908 Series: Hard sub-micron substrate with TiAlN PVD coating. Suitable for low to medium cutting speeds. Developed for machining refractory alloys, austenitic stainless steels and very hard steels. High resistance to embossing, oxidation. Suitable for a wide variety of materials and engaging conditions. Usage: Steel: P10-P30 (Vc = 70-180 m / min; 230-590sfm; Fn = 0,04-0,12 mm / rev.) Stainless steel: M05 -M20 (Vc = 50-180 m / min; 160-590 µm; Fn = 0.04-0.12 mm / rev.) Cast iron: K15-K30 (Vc = 110-175m / 570 sfm; Fn = 0,04-0,12 mm / rev.) Non-Ferrous Metals and Plastics: N05-N20 Superslitz: S05-S20 Hardened: H05-H15 Tough conditions - see enclosed photo Type J: For cutting and grooving pipes, smaller diameters and thin-walled materials Ref. No. 6002961

Grooving insert, replaceable insert for turning - grooving DGN1000P IC508, Iscar Grooving width: 1.0mm Coating: PVD, TiCN TiN >IC508 series: Tough submicron substrate with TiCN TiN PVD coating. Designed for a wide range of materials at low to medium cutting speeds, intermittent cutting and unstable conditions. Highly resistant to notch wear and build-up. Usage: Steel: P20-P40 Stainless steel: M20-M30 Cast iron: K20-K30 Non-ferrous metals and plastics: N10-N30 Superalloys: S10- S40 Carbide: H10-H20 Cutting conditions - see attached photo Type P: Dividing and grooving of soft (sticky) materials, thin and small workpieces. Very sharp breaker geometry - similar to a polished blade. Order no. no.: 6003280 The price shown is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.