Threads

Reversible tapping head / reversing tap Clamping range: according to the selected variant Clamping shank (morse taper): according to the selected variant Other dimensions - see the description for each variant Type K1 is with a drill chuck, types K2, K3 and K4 are with clamping behind the stones After cutting the set depth, the speed will change The tap is without a torque coupling, ie it does not protect the tap from bending. Instructions for use - see attached PDF

Reversible tapping head / reversing tap Clamping range: according to the selected variant Clamping shank (cylindrical): according to the selected variant Other dimensions - see the description for each variant Type K1 is with a drill chuck, types K2, K3 and K4 are with clamping behind the stones After cutting the set depth, the speed will change The tap is without a torque coupling, ie it does not protect the tap from bending. Instructions for use - see attached PDF

Special collet for clamping taps into a VTA reverse tap with torque coupling Clamping range of the collet: see label for individual variants Diameter and other dimensions: see label for individual variants To two collets fit each Vertex VTA thread cutter: VTA7-JT6 thread cutter: FC-10 (2.5-4.5mm) and FC-11 (4.5-6.5mm) collets Tap cutter VTA12-JT6 : collet FC-20 (4.0-7.0mm) and FC-21 (7.5-10.0mm) Tap cutter VTA20-M20 : collet FC-30 (8.0 -12.0mm) and FC-31 (14.0-19.0mm)

Quick-clamping tapping head with length compensation for bits for machine taps according to DIN371 DIN374 and DIN376 Clamping range of the tap: according to the selected variant Clamping shank (steep ISO cone): according to the selected variant Standard: JIS 6339 BT The torque coupling is set directly on the attachment. Tap clamping method: Taps are clamped in extensions, which need to be purchased separately. The taps are secured in the extension with a square and a clamping shank. The tap is held firmly in the extension, pulled out after pressing the clamping collar. The extensions are secured in the head over a bearing and stones. In addition to the tapping head, it is also possible to purchase additional attachments for taps manufactured in accordance with JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps manufactured according to DIN371,374,376 standards Clamping tongs TC-312 / TC-820 / TC-1433 are not part of the tap - they need to be purchased separately! Usage: The tap is clamped in a suitable attachment, which has a torque coupling already preset, or it can be fine-tuned as needed.

Quick-clamping tapping head with length compensation for bits for machine taps according to DIN371 DIN374 and DIN376 Clamping range of the tap: according to the selected variant Clamping shank (steep ISO cone): according to the selected variant Standard: DIN69871 The torque coupling is set directly on the attachment. Tap clamping method: Taps are clamped in extensions, which need to be purchased separately. The taps are secured in the extension with a square and a clamping shank. The tap is held firmly in the extension, pulled out after pressing the clamping collar. The extensions are secured in the head over a bearing and stones. In addition to the tapping head, it is also possible to purchase additional attachments for taps manufactured in accordance with JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps manufactured according to DIN371,374,376 standards Clamping tongs TC-312 / TC-820 / TC-1433 are not part of the tap - they need to be purchased separately! Usage: The tap is clamped in a suitable attachment, which has a torque coupling already preset, or it can be fine-tuned as needed.

Quick-clamping tapping head with length compensation for bits for machine taps according to DIN371 DIN374 and DIN376 Clamping range of the tap: according to the selected variant Clamping shank: according to the selected variant The torque coupling is set directly on the attachment. Tap clamping method: Taps are clamped in extensions, which need to be purchased separately. The taps are secured in the extension with a square and a clamping shank. The tap is held firmly in the extension, pulled out after pressing the clamping collar. The extensions are secured in the head over a bearing and stones. In addition to the tapping head, it is also possible to purchase additional attachments for taps manufactured in accordance with JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps manufactured according to DIN371,374,376 standards Clamping tongs TC-312 / TC-820 / TC-1433 are not part of the tap - they need to be purchased separately! Usage: The tap is clamped in a suitable attachment, which has a torque coupling already preset, or it can be fine-tuned as needed.

3-jaw tap chuck Clamping (inner B cone or outer morse taper): according to the selected variant Number of jaws: 3 + square clamping Other dimensions - see description for individual variants Tightens by turning the threaded head in which there are three jaws, then the enclosed Allen key and two internal stop jaws for attaching the square shank of the tap.

Double-jaw chuck with Allen key for firm clamping of taps Clamping range: according to the selected variant Clamping cone (internal): according to the selected variant Other dimensions - see the description of the selected variant We recommend use from M12, for smaller taps use a classic 3-jaw chuck, or a three-jaw chuck with square clamping - type VTA

Quick-clamping tapping head without length compensation for attachments for machine taps according to DIN371 DIN374 and DIN376 Clamping range of the tap: according to the selected variant Clamping shank: according to the selected variant This type (SF) is without length compensation! The torque coupling is set directly on the attachment. Tap clamping method: Taps are clamped in extensions, which need to be purchased separately. The taps are secured in the extension with a square and a clamping shank. The tap is held firmly in the extension, pulled out after pressing the clamping collar. The extensions are secured in the head over a bearing and stones. In addition to the tapping head, it is also possible to purchase additional attachments for taps manufactured in accordance with JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps manufactured according to DIN371,374,376 standards Clamping tongs TC-312 / TC-820 / TC-1433 are not part of the tap - they need to be purchased separately! Usage: The tap is clamped in a suitable attachment, which has a torque coupling already preset, or it can be fine-tuned as needed.

Quick-clamping tapping head with length compensation for bits for machine taps according to DIN371 DIN374 and DIN376 Clamping range of the tap: according to the selected variant Clamping shank (cylindrical): according to the selected variant Clamping shank length: see description for variant The torque coupling is set directly on the attachment. Tap clamping method: Taps are clamped in extensions, which need to be purchased separately. The taps are secured in the extension with a square and a clamping shank. The tap is held firmly in the extension, pulled out after pressing the clamping collar. The extensions are secured in the head over a bearing and stones. In addition to the tapping head, it is also possible to purchase additional attachments for taps manufactured in accordance with JIS and ISO 529 standards, which are not common in our country. Approximately 90% of the domestic market consists of taps manufactured according to DIN371,374,376 standards Clamping tongs TC-312 / TC-820 / TC-1433 are not part of the tap - they need to be purchased separately! Usage: The tap is clamped in a suitable attachment, which has a torque coupling already preset, or it can be fine-tuned as needed.

Air tap with adjustable arm Range: according to the chosen variant * The range depends only on the VAT-SP tapping head, ie if you want a larger tapping range, you only need to buy a head with a different range - see related products. Min. compressor power: 5HP (corresponds to 3.8kW) Required pressure: 6-7 bar Air consumption: 940 l / min Arm positionability: Rmax 700mm Contains 6 pcs of TC type extensions - the size of the extensions is stated in the description for individual variants. The attachments have a torque coupling for taps manufactured according to DIN371 and DIN376. You can find the specific attachment sizes in the label for each variant Additional adapters can be purchased - see related products. Includes air pressure regulator with separator and lubricator. Cast iron clamping plate not included! The tapping head works at a pressure of 6-7 bar, the inlet air must be dry and clean. Regularly add suitable pneumatic oil to the lubricator container. Use suitable cutting oil when threading. After one hour of operation, allow the head to cool for 10-15 minutes. Clean and inspect the head at 3-month intervals. Before each thread cutting, check that the machined surface is parallel to the tapping arm (correct threading in the axis). If the tapping machine is not in stock, the delivery date can be immediately - for the tapping machine it is enough to switch the tapping head for a type with a different range - we have VAT-SP tapping heads themselves in stock.

Air tap with adjustable arm Range: according to the chosen variant * The range depends only on the VAT-SP tapping head, ie if you want a larger tapping range, you only need to buy a head with a different range - see related products. Min. compressor power: 5HP (corresponds to 3.8kW) Required pressure: 6-7 bar Air consumption: 940 l / min Arm positionability: Rmin. 200mm, Rmax 1400mm Contains 6 pcs of TC type extensions - the size of the extensions is stated in the description for individual variants. The attachments have a torque coupling for taps manufactured according to DIN371 and DIN376. You can find the specific attachment sizes in the label for each variant Additional adapters can be purchased - see related products. Includes air pressure regulator with separator and lubricator. Cast iron clamping plate not included! The tapping head works at a pressure of 6-7 bar, the inlet air must be dry and clean. Regularly add suitable pneumatic oil to the lubricator container. Use suitable cutting oil when threading. After one hour of operation, allow the head to cool for 10-15 minutes. Clean and inspect the head at 3-month intervals. Before each thread cutting, check that the machined surface is parallel to the tapping arm (correct threading in the axis). If the tapping machine is not in stock, the delivery date can be immediately - for the tapping machine it is enough to switch the tapping head for a type with a different range - we have VAT-SP tapping heads themselves in stock.