Milling

Set of 18 pcs of ER 32 collets made of stainless steel on wooden board, ER32 collets Diameters: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20 mm Pliers can be clamped: - Up to 2.5 mm diameter 0.5 mm - From 3 mm diameter 1.0 mm Accuracy : 0,005mm Material: INOX / stainless steel Standard: DIN 6499B / 470ESP Collet clamping procedure: Snap the collet into the clamping nut - according to the attached picture .

ER40 ER40 , 19, 20, 22, 26, 30 mm Collet clamping procedure: Screw the clamp into the clamping nut - according to the attached picture.

Set of 21 collets ER 40 on a wooden board, collets ER40 Diameters: 3 , 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13 , 14 , 15 , 16 , 17 , 18 . 0.015mm Standard: DIN 6499B / 470E Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.

Set of 24 sealed collets ER 40 for use with tools with internal cooling, collets ER40 Diameters: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 , 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26 mm Collet clamping procedure: Snap the collet into the clamping nut - according to the attached picture. standards Standard: DIN6499C / 472EA Max. pressure tested by the manufacturer: 40bar Tools with internal cooling are not produced with a shank smaller than 3mm, so this set starts from a diameter of 3mm.

Set AKKO 10 pcs WALTER ADMT 160612R-F56 ??WSP45S WALTER * Length 150mm without internal cooling! Diameter: 25mm Angle: 90 ° Number of Cuts: 2 Clamping Diameter: 25 mm Overall Length: 150 mm Working Length: 50 mm VBD Cutting Edge: 15mm Bolts: 1515-M4x9 / T15 Type VBD: 1) ADMT 1606 Packaging incl. 10pcs VBD ADMT 160612R-F56 ??WST45S Steel: P30-P50 Stainless Steel: M30-M50 Superslitin (Ni, Co, Fe, Ti): S30-S50 AKKO MAKINA drilling mowers are an economical and at the same time very high quality solution for your production. Heat-treated milling body material, special heat-resistant coating and aggressive materials, precision machining of the body and insert bush, and the Swiss SFS joint material guarantee the quality and long life of AKKO tools.

Set AKKO 10 pcs WALTER ADMT 160612R-F56 ??WSP45S WALTER * Length 150mm without internal cooling! Diameter: 32mm Angle: 90 ° Number of Cuts: 3 Clamping Diameter: 32 mm Overall Length: 150 mm Working Length: 50 mm VBD Cutting Edge: 15mm Bolts: 1515-M4x9 / T15 Type VBD: 1) ADMT 1606 Packaging incl. 10pcs VBD ADMT 160612R-F56 ??WST45S Steel: P30-P50 Stainless Steel: M30-M50 Superslitin (Ni, Co, Fe, Ti): S30-S50 AKKO MAKINA drilling mowers are an economical and at the same time very high quality solution for your production. Heat-treated milling body material, special heat-resistant coating and aggressive materials, precision machining of the body and insert bush, and the Swiss SFS joint material guarantee the quality and long life of AKKO tools.

Extra short reduction insert with morse cavity, ISO40 / MK4, 40/4, 40x4 - . Internal cone: Morse, MK 4 Length: 60 mm (specifies the length of the case that will protrude out of the machine) Standard: replacement for DIN 2080, ČSN 247213, 220432 Strength: Case quenched, then ground (like all others). This type of case was manufactured in the 1960s as an accessory for TOS milling machines Usage: Clamp / mandrel for milling cutters < / b> with Taper Shank MK4 For Clamping with ISO40 Conical Milling Machine Clamping Procedure: After inserting the sleeve into the spindle, the sleeve is fixed over two screws firmly to the spindle machinery. The tool is inserted directly into the sleeve, the sleeve is through, so the tool is tightened directly, in the case of the MK4 cone with the M16 screw.

Simple cutting jig for ER25 collets with square shank / clamping For ER25 collets(outer diameter 25mm) Max. size of collet that goes into this chuck: 16mm ER25 collets can be purchased separately - see related products Clamping shank: square 35mm Length of clamping part: 42mm Total length of clamp: 68mm Clamping nut diameter: 42mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 18.5mm Application: For square milling / grinding.

Simple cutting jig for ER32 collets with square shank / clamping For ER32 collets(outer diameter 32mm) Max. size of collet that goes into this chuck: 20mm ER32 collets can be purchased separately - see related products Clamping shank: square 40mm Length of clamping part: 42mm Total length of clamp: 70mm Clamping nut diameter: 50mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 24mm Application: For square milling / grinding.

Simple cutting jig for ER40 collets with square shank / clamping For ER40 collets(outer diameter 40mm) Max. size of collet that goes into this chuck: 30mm ER40 collets can be purchased separately - see related products Clamping shank: square 44.5mm Clamping part length: 48mm Total length clamps: 80mm Clamping nut diameter: 63mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 28mm Application: For square milling / grinding.

Safety valve with seal - 10bar / atm Function: At higher pressure in the distribution, the pressure that the spring develops on the ball inside the valve is overcome. This will open, respectively. bounce the ball and release the hole - on the photo. This valve should only serve as a secondary overpressure protection - ie if an electric or mechanical control valve fails.

TPCN 1603 ODT / PDT / TPCN 1603 PDSN H10 Angle Adjustment: P (90 °) Face Angle Angle: D (15 °) Cutting Edge Design: S (Rounded Edges with Facet) Feed Direction: N - Neutral - Feed Right & Left Material of slicer: H10 (uncoated) Usage: Lithium: K10