Milling inserts with inserts

Milling insert for hardened steel, replaceable insert, insert APGW 160408 HRC55 Suitable for holders for APKT 1604 or APMT 1604 inserts Radius: 0.8mm Material: CBN(1x) CBN coating: uncoated HRC55 Series: Fine-grained 70% CBN granulate with ceramic binder, high rigidity and impact resistance. Suitable for roughing hardened steels 45-65 HRC, cast iron and very hard alloys such as Inconel, surface hardened steels, etc. Suitable for intermittent cutting. Application: Cast iron: K05-K15 Carbide and hardened steels: H10-H25(45-65 HRC) Cutting conditions(CBN): Hardened steel: Vc = 80-240m / min; fn = 0.12-0.25mm / rev. ; Ap = 0,5-2,5mm Ductile iron: Vc = 60-150m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.6-2.5mm Gray cast iron: Vc = 500-1500m / min; fn = 0.50-0.80mm / rev. ; Ap = 0.25-1.0mm Hard alloys with Co> 17%: Vc = 20-40m / min; fn = 0.20-0.30mm / rev. ; Ap = 0.1-0.5mm Manganese steels: Vc = 140-200m / min; fn = 0.3-0.7mm / rev. ; Ap = 0,2-2,9mm The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pcs in the basket.

Replacement Inserts VBD TPUN 160308 IC830 Radius 0,8mm Coating: PVD, AlTiN TiN IC830 Series: Suitable for intermittent cutting and roughing of stainless steel, classical steels and heat-resistant alloys. High stiffness and wear resistance. Usage: Steel: P20-P40 Stainless Steel: M25-M35 Superslitz: S15-S30 Terms and conditions - see attached photo Cat. No .: 3308119

APMT 15T3 PDR - F56 WMG40 Cat. No. 0412827788

VBD TPUN 220412 IC20 IC20 Series: Suitable for routine and finishing operations, roughing of aluminum, cast iron and stainless steel. Uses: Stainless Steel: M10-M25 Cast Iron: K10-K20 Non Ferrous Metals & Plastics: N05-N25 Superslitz: S05-S20 H05- H15 Terms and conditions - see attached photo Kat. No. 05502380

Insert VBD SPUN 120308 IC9054 Radius 0,8mm Coating: CVD, TiCN Al2O3 TiN series IC9054: High rigidity, suitable for machining carbon alloys, steel alloys and stainless steels at normal and higher cutting speeds. Usage: Steel: P15-P40 Stainless steel: M10-M30 Terms - see attached photo Cat. Ä. : 5507587 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

VBD TPUN 110304 IC9054 Radius 0.8mm Coating: CVD, TiCN Al2O3 TiN IC9054 Series: High rigidity, suitable for machining carbon alloys, steel alloys and stainless steel at normal and higher cutting speeds. Usage: Steel: P15-P40 Stainless Steel: M10-M30 Terms and conditions - see attached photo Cat. No .: 5507595

VBD TPUN 220408 IC9054 Radius 0.8mm Coating: CVD, TiCN Al2O3 TiN IC9054 Series: High rigidity, suitable for machining carbon alloys, steel alloys and stainless steel at normal and higher cutting speeds. Usage: Steel: P15-P40 Stainless Steel: M10-M30 Terms and conditions - see attached photo Cat. No .: 5507598

VBD TPUN 160308 IC3028 IC3028 Series: The toughest series for machining stainless steel, heat-resistant alloys at low and medium speeds, intermittent cut, roughing operations with larger chipping. Usage: Steel: P25-P45 Stainless Steel: M15-M35 Superslitz: S20-S30 Terms of use - see attached photo Cat. No. 5597228

VBD APKT 1003 PDR - HM IC20 IC20 Series: Suitable for routine and finishing operations, roughing aluminum, cast iron and stainless steel. Plates are especially recommended for machining non-ferrous metals - aluminum, copper, brass, plastics, etc., or cutting / sharpening / casting to reduce the chip and the feed to a minimum. Uses: Stainless Steel: M10-M25 Cast Iron: K10-K20 Non Ferrous Metals & Plastics: N05-N25 Superslitz: S05-S20 H05- H15 Terms and conditions - see attached photo HM Type: General use Cat. : 5600047

Milling insert VBD TPKN 2204PDTR-42 IC328 Coating: PVD, TiCN IC328 series: Thin PVD coated TiCN layer on carbide P45-K40. Very high rigidity - resistance to chipping. Suitable for machining steels, stainless steels and alloy steels at low to medium speeds, at unstable engagement conditions(spins ovanA1 A ™ ez). Usage: Steel: P25-P50 Stainless steel: M30-M40 Superalloys: S25-S30 Terms and conditions - see attached photo Type -42: Beveled edge -> plates are without radius. Longer plate life. Contact the Company: Kat. Ä. : 5601262 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Milling insert VBD TPKR 1603PPTR-HS IC328 Coating: PVD, TiCN IC328 series: Thin PVD coated TiCN layer on carbide P45-K40. Very high rigidity - resistance to chipping. Suitable for machining steels, stainless steels and alloy steels at low to medium speeds, at unstable engagement conditions(spins ovanA1 A ™ ez). Usage: Steel: P25-P50 Stainless steel: M30-M40 Superalloys: S25-S30 Terms and conditions - see attached photo Type HS: Type with uneven / stepped blades for chip splitting and lower vibration. Contact the Company: Kat. Ä. : 5601306 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Milling insert VBD TPKN 1603PPTR-42 IC328 Coating: PVD, TiCN Series IC328: Thin PVD coated TiCN layer on carbide P45-K40. Very high rigidity - resistance to chipping. Suitable for machining steels, stainless steels and alloy steels at low to medium speeds, at unstable engagement conditions(spins ovanA1 A ™ ez). Usage: Steel: P25-P50 Stainless steel: M30-M40 Superalloys: S25-S30 Terms and conditions - see attached photo Type -42: Beveled edge -> plates are without radius. Longer plate life. Contact the Company: Kat. Ä. : 5601315 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.