Metalworking tools

Drilling insert VBD SPMG 140512 DG TT9030 Radius: 1,2mm Insert material: 9030 Universal insert for machining P(steel), M(stainless steel) and S(heat-resistant steel). Steel: P20-P40 Stainless steel(abrasion resistant): M20-M40 Superalloys(Ni, Co, Fe, Ti): S20-S40 Cat . A „. : 5516697 The price is for 1 piece, not for the whole package, if you want to buy the whole package, put 10 pieces in the basket.

Simple cutting jig for ER25 collets with square shank / clamping For ER25 collets(outer diameter 25mm) Max. size of collet that goes into this chuck: 16mm ER25 collets can be purchased separately - see related products Clamping shank: square 35mm Length of clamping part: 42mm Total length of clamp: 68mm Clamping nut diameter: 42mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 18.5mm Application: For square milling / grinding.

Simple cutting jig for ER32 collets with square shank / clamping For ER32 collets(outer diameter 32mm) Max. size of collet that goes into this chuck: 20mm ER32 collets can be purchased separately - see related products Clamping shank: square 40mm Length of clamping part: 42mm Total length of clamp: 70mm Clamping nut diameter: 50mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 24mm Application: For square milling / grinding.

Simple cutting jig for ER40 collets with square shank / clamping For ER40 collets(outer diameter 40mm) Max. size of collet that goes into this chuck: 30mm ER40 collets can be purchased separately - see related products Clamping shank: square 44.5mm Clamping part length: 48mm Total length clamps: 80mm Clamping nut diameter: 63mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 28mm Application: For square milling / grinding.

Tire Pressure Gauge (Tire Pressure Gauge) Alarm Diameter 63mm, Rubber Case Scale: 0- 12 Bar. 0 - 170 PSI Rear 1/4 "Male Thread 1 Manometer can be used to check the piston in the pneumatic circuit or as a spare part for the ZG-3

Tire Pressure Gauge (Tire Pressure Gauge) Alarm Diameter 63mm, Rubber Case Scale: 0- 4 Bar, Gentle Division 0-1,1 Bar Underground Male Thread 1/4 "G" Pressure gauge can be used for pneumatic circuit control, as a spare part for ZG-3 type tire filler

Self-locking chuck with short morse cone MK2, type SOLID Clamping range: 1-13 mm Clamping shank: morse 2 Clamping lenght: 25mm Clamping screw thread: M6 ( M6x1,0) Head diameter: 51,2mm Accuracy: up to 0,03mm Application: This chuck is inserted into "monolithic assemblies" - mostly with ISO40 cone - see related products

Replacement Capillary Pressure Indicator for CO2 Reduction Valves Range 0-25 Mpa Diameter Outside Thread: 13.8mm Flow Rate: 0 to 25 l / min - By Ball in Capillary Thread under capillary: M12x1,0 Nipple under capillary: 8mm

Safety valve with seal - 10bar / atm Function: At higher pressure in the distribution, the pressure that the spring develops on the ball inside the valve is overcome. This will open, respectively. bounce the ball and release the hole - on the photo. This valve should only serve as a secondary overpressure protection - ie if an electric or mechanical control valve fails.

- .

Pressure Gauge with Rubber Hose, Tire Pressure Gauge, Double Sided Tip Range: 0-12 bar, 0-170 PSI Diameter of Manometer: 55mm, Rubber Case Hose Length with Tip: 600mm

° C Container volume: 50 cm3 Container made of high quality polycarbonate Dimensions: 145x55mm Recommended oil in the lubricator: Velocite 6 Cutting and Do not use Bearing Oil !!! Input is marked on the body of the lubricator with an arrow. Never connect the lubricant to the opposite direction!