Metalworking tools

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. After inserting a knife with a 6mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of ( axial height) 16mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Length of holder: 77mm Width: 18mm Height: 24mm Photo is illustrative, shows holder for larger knife

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head settle the blade in the correct position and axial height of 12 mm after landing on the knife surfaces. After inserting a knife with a 10mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axis height) 12mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Holder length: 64mm Width: 12mm Height: 12mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. The holder is double-sided - it is therefore possible to clamp knives with a diameter of 10 mm and 12 mm. In both cases for an axial height of ( edge height) 16mm If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 76mm Width: 18mm Height: 16mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head settle the blade in the correct position and axial height of 12 mm after landing on the knife surfaces. After inserting a knife with a 12mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axis height) 12mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate pads under the holder. Holder length: 64mm Width: 10mm Height: 10mm

This guide pad is used for easy and parallel clamping of a turning knife with a cylindrical shank in the knife head. The knife is inserted into the holder and the clamping screws in the knife head, after landing on the knife surfaces, settle the blade in the correct position and axial height of 16 mm. After inserting a knife with a 12mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axis height) 16mm. If you have a lathe for knives with an axial height higher than 12mm, you must add adequate washers under the holder. Holder length: 64mm Width: 10mm Height: 16mm

Clamping holder for knives with a circular shank diameter 6mm. The knife is fixed inside the holder using 3 screws with an IMBUS head. The holder with the knife clamped is then inserted into the knife head. After inserting a knife with an 8mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axial height) 16mm. If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 77mm Width: 18mm Height: 24mm

Clamping holder for knives with a circular shank diameter 6mm. The knife is fixed inside the holder using 3 screws with an IMBUS head. The holder with the knife clamped is then inserted into the knife head. After inserting a knife with an 8mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axial height) 16mm. If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 77mm Width: 18mm Height: 24mm

Clamping holder for knives with a circular shank diameter 8mm. The knife is fixed inside the holder using 3 screws with an IMBUS head. The holder with the knife clamped is then inserted into the knife head. After inserting a knife with an 8mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axial height) 16mm. If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 77mm Width: 18mm Height: 24mm

Clamping holder for knives with a circular shank diameter 8mm. The knife is fixed inside the holder using 3 screws with an IMBUS head. The holder with the knife clamped is then inserted into the knife head. After inserting a knife with a 10mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axis height) 16mm. If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 77mm Width: 18mm Height: 24mm

Clamping holder for knives with a circular shank diameter 8mm. The knife is fixed inside the holder using 3 screws with an IMBUS head. The holder with the knife clamped is then inserted into the knife head. After inserting a knife with a 12mm shank and an exchangeable plate into this holder, you will therefore achieve a blade height of (axis height) 16mm. If you have a lathe for knives with an axial height higher than 16mm, you must add adequate washers under the holder. Holder length: 77mm Width: 18mm Height: 24mm

Additional support - milling support, support for hobby lathes Clamping area: 100x125mm Axial feed - aligned with base plate: 65mm Axial feed - maximum !LnA: 80mm Vernier: 1 length of vernier 0,02mm, 1x turn = 2mm Base: 92x80mm Mounting holes: 2x 10mm, pitch 41mm T-grooves: 3x T10, pitch 40mm Bronze nut, feed bronze nut. Prismatic guide with delimiter bar and feed lock option. Application: Mounted on the cross support of the lathe.

Additional support - milling support, support for hobby lathes Clamping area: 50x90mm Axial feed - aligned with base plate: 30mm Axial feed - maximum f!LnAf: 54mm Vernier: 1 length of vernier 0,03mm, 1x turn = 1,5mm Base: 57x50mm Mounting holes: 2x 5mm, pitch 22mm T-grooves: 3x T5,5, pitch 25,5mm 2x T4 on the sides Part is a simple clamping plate. Bronze nut, feed with bronze nut. Prismatic guide with delimiter bar and feed lock option. Application: Mounted on the cross support of the lathe.