Metalworking tools

Machine chuck for external edges / machine needle Range: 60-97mm Bevel angle: 90 Number of slots for edge inserts : 2 Clamping shank: MK3(morse 3) n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for external edges / machine needle Range: 80-117mm Bevel angle: 90° Number of slots for edge inserts : 2 Clamping shank: MK3(morse 3) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: XXmm Diameter of the front part: XXmm Diameter of aluminum nuts: XXmm and XXmm Length of clamping shank: XXmm How to insert the blade and set the height of the needles / chamfers Edges 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Run for 90 ° machine needle 02-010 by KOPAL. Shrink angle: 90 ° Podbrus blade: 14 ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. Ä. : 02-300

Run for 90 ° machine needle 02-010 by KOPAL. Shrinkage angle: 90 ° Podbrus blade: 20 ° Material: HSS Coating: uncoated Usage: suitable for Stainless steel, swords, plastics, stainless steel You can compare the differences in the undercut table in the attached photos. Knife dimensions: 30 x 8,7mm Cat. Ä. : 02-302

Run for a 60 ° machine needle 02-020 from KOPAL. Shrinkage angle: 60 ° Podbrus blade: 0 ° Material: HSS Coating: uncoated Usage: suitable for brass , bronze, cast iron, heat-resistant steel You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. Ä. : 02-303

Run for 90 machine ° machine needle 02-010 by KOPAL. Chamfer angle: 90 ° Podbrus sharp: 0 Â ° Material: HSS Coating: uncoated Application: suitable for brass, bronze, cast iron, heat-resistant steel You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. A „. : 02-304

Run for a 60 machine ° machine needle 02-020 from KOPAL. Shrinkage angle: 60 ° Podbrus blade: 14 Â ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. A „. : 02-305

Run for 90 ° machine needle 02-010 by KOPAL. Shrinkage angle: 90 ° Podbrus blade: 25 ° Material: HSS Coating: uncoated , Iron, Sheets You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. Ä. : 02-306

Run for 60 ° machine needle 02-010 by KOPAL. Shrinkage angle: 60 ° Podbrus blade: 25 ° Material: HSS Coating: uncoated Application: suitable for aluminum , Iron, Sheets You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 30 x 8,7mm Cat. Ä. : 02-307

Run for a 60 machine ° machine needle 02-020 from KOPAL. Shrinkage angle: 60 ° Podbrus blade: 20 Â ° Material: HSS Coating: uncoated Usage: suitable for Stainless steel, swords, plastics, stainless steel You can compare the differences in the undercut table in the attached photos. Knife dimensions: 30 x 8,7mm Cat. A „. : 02-308

Run for 90 ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Shrink angle: 90 ° Podbrus blade: 14 ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 69x20 x 8,7mm Cat. Ä. : 02-310

Run for 90 Â ° machine needlers 2-36mm to 80-120mm for chamfering the outer edges of the KOPAL brand. Chamfer angle: 90 ° Podbrus sharp: 0 Â ° Material: HSS Coating: uncoated Application: suitable for brass, bronze, cast iron, heat-resistant steel You can compare the differences in the tablecloth in the attached photos. Knife dimensions: 69x20 x 8,7mm Cat. A „. : 02-312