Metalworking tools

Clamping range: 5,6-16,0 mm ČSN 241126

Clamping range: 3,15-6,3 mm ČSN 241126

Absolute and relative measurements, 4 workspaces. Display flips depending on device position. Measuring frame made of aluminum Resolution 0.1 ° Accuracy 0.1 ° for 0-90 ° and up to 0.2 ° for> 90 °. Calibration is done by pressing the ON / OFF button while the power is turned off. Then turn it back on again, the value "1" will melt. Press the ZERO button, wait for 6 seconds. then turn the inclinometer 180 ° and press ZERO again and wait for 6 seconds. You have an absolute zero set and the calibrator is calibrated.

Digital magnetic spirit level with IP65 protection Absolute and relative measurement, 4 work surfaces The display flips according to the position of the device. Resolution 0.1 ° Accuracy 0.1 ° for 0-90 ° and up to 0.2 ° for> 90 °. Calibration is performed by pressing the ON / OFF button while turning it on until the instrument turns off. Then switch it on again, the value "1" lights up. Press the ZERO button, wait 6sec. then turn the inclinometer 180 ° and press ZERO again and wait 6 seconds. You have set absolute zero here and the inclinometer is calibrated.

Digitometer with Magnet / Magnets 0-360 ° Always displayed 0-90 ° angle Dimensions of base: 50x50mm

Pocket digital spirit level 65x50mm with upper libel and magnetic base Leveling digital protractor for fast angle viewing Magnetic base, shutdown when inactivity 5 min, reset button Absolute Zero Absolute Zero Measures Precision 0.1 ° Protractor Dimensions: Length: 51mm Width: 32mm Height: 62mm

Rotary slicer PTGNL 2525 P 22, 90 ° Rotary knife PTGNL-2525P22, 90 ° Cutter size: 25x25 mm Front angle: -6 ° Angle of inclination blade: -6 ° Plate height: 25mm Overall length of blade: 170mm Interchangeable pads have TNM markings. 2204.- E (ie TNMG 2204 ..- E, TNMA 2204 ..- E, etc.)

SK Carbide / Carbide Cutter Material: TK (SK) Type: Taper Shaft - KEL Type Cutter Diameter: 10mm Cutting Length: 20mm Overall Length: 60mm Diameter of chucking stem: 6mm Application: Cross teeth are suitable for machining difficult to process materials Highly alloyed steel, cast iron, stainless steel, refractory steel < br> Suitable for chamfering, deburring, deburring, surface repair after welding, surface shaping Cat. No .: 21125087

Collet holder HSK F 63 ER 40 - 75 mm Type HSK F63 ER40 AD - cooling guided through the center Length from cone to holder: 75mm Max. collet size: 30mm For collets with outer diameter: 40mm Diameter of clamping nut: 62mm Clamping stem design for aut. replacement: DIN69893 F ER40 collets can be purchased additionally. Throwability: up to 0.005mm Balance: G6.3 / 20,000 rpm. Standard: DIN 69893 The collar has a hole for a data carrier according to DIN69873 (Balluffchip) Cat. no.: F63.02.26

Hook wrench with tooth for quick-release chuck The chuck for which the key is intended can be found in the related products. The key may not fit chucks from other suppliers/manufacturers.

Regofix collet chuck HSK-A 63 x ER32 - 100mm Type HSK A63 ER32 AD - center-cooled cooling Length from cone to chuck: 100mm Max. collet size: 20mm For collets with outer diameter: 32mm Clamping nut diameter: 49mm Clamping shank design for cars. exchange: DIN69893 A ER32 collets can be purchased separately. Throw: up to 0.005mm Balance: G6.3 / 20,000 rpm. Standard: DIN 69893 There is a hole in the collar for a data carrier according to DIN69873(Balluffchip)

Velcro polishing pad with a diameter of 150 mm