Metalworking tools

Carbide drill for drilling bent taps For tap: M12 d1(H7): 10,20 mm Max. depth l3: 35mm Total length l1: 80mm Clamping shank: cylindrical 12 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0070

Carbide drill set for drilling bent taps For taps: M3 - M4 - M5 - M6 - M8 - M10 - M12 d1(H7): 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm Max. depth l3: 10/14/19/23/23/25/35 mm Total length l1: 38/46/50/50/60/80/80 mm Clamping shank: cylindrical Hexagon < br> Helix angle: 0  ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1865

15', , 1 °, 2 °, 3 °, 4 °, 5 °, 10 °, 15 °, 20 °, 25 °, 30 ° Accuracy: 0.003mm Hardness: 48-53 HRC < br> No .: 2006-001

Range: Convex Radius: R0 - R40 (mm) Concave radius: R0 - R90 (mm) Diamant hole: 10mm No diamond tip !!!

Balancing stand, grinding wheel balancer For max. 500mm diameter balancing item Adjustable pitch for wheel up to width 230mm Wheels made of high quality material, 55 HRC Other dimensions see photo < br> Order no. No .: 2014-001

Balancing stand, grinding wheel balancer For maximum diameter of balancing item 200mm Other dimensions see photo Item no. No: 2014-010

Balancing stand, grinding wheel balancer For maximum diameter of balancing item 350mm Other dimensions see photo Item no. No: 2014-011

Lamel Magnetic Block Polar Pitch: 2,5 3mm Suitable for permanent magnets and electromagnets. Width: 50mm Height: 25mm Lenght: 100mm Lamellar Blocks allow you to create an optimal clamping surface for workpieces that can not be clamped to the classical surface of a magnetic clamping plate . It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Ref. No. 2015-401

Lamellar prism magnetic block Poles pitch: 2,5 3mm Suitable for permanent magnets and electromagnets. Width: 60mm Height: 48mm Length: 110mm Laminar Prismatic Blocks allow you to create an optimal clamping surface for workpieces that can not be clamped on to the classical surface of a magnetic clamp plates. It also serves to direct the magnetic field into the workpiece, especially in cases where the existing magnetic field of the clamp is not suitable for the workpiece. Another benefit is the possibility of additional machining (machining) of this block for differently shaped workpieces. Ref. No. 2015-403

Magnetic holder for diamond dresser Holder without diamond dresser. Diamond cutting edges can be purchased Clamping eye is 12mm diameter Magnetic cube: 60x50x55 mm Clamping force: 80kg (800N)

Magnetic base with 1 metal 1/4 "hose for cooling, lubrication or blowing Cooling hoses for cooling in metalworking 1pcs flexible hoses are attached to a magnetic cube with valves. > Nozzle diameter: 4mm Hose length: 30cm Inlet nipple for hose: 9mm Max bending radius: 330mm Magnetic cube has bottom prism, base dimensions 64x51x54 / 81mm Pressure: 80N (75kgs) Order No.: 2015-642

Magnetic Thread Cutting Stand Range: M3 - M12 Suitable for large workpieces, sheet metal cutting, planking ... Horizontal and vertical use < br> Pressure: 80kg (800N)