Insert for M5 tap with torque coupling, TC-312-M5-DIN376, 312-24D

M3 - M12 Clamping shank: Straight ISO40 < br> Standard: DIN69871 Clamping kit sets: DIN 371 (reinforced shank): M3; M4; M4.5; M5; M6; M7; M8; M10 DIN 376 (classical shank): M4,5; M5; M6; M8; M12 Length compensation - see photo no.3, no.4 and no.12 The set is delivered in the trunk - see photo 9 and no.10 Taper clamping method: The taps are secured in the extension behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo no.5 and no.6 Expansion of the attachment see photo no.7 and no.8 You can buy the set Taps for M1 - M16 taps - see photo n ° 11 Taps for taps manufactured according to JIS and ISO 529 standards, which are not common in our country, are also available for tapping heads. About 90% of the domestic market consists of taps made to DIN standards Taps are not a part of the set! The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: 32mm, cylindrical Clamping length: 70mm Clamping method: < / b> The taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Thin-clamping head with length compensation for TC 312 for machine taps according to DIN371 DIN374 and DIN376 Clamping range of thread cutting: M1 - M14 (need to buy TC312 collet) Clamping shank: 20mm, cylindrical < Clamping Shank Length: 70mm Tape Clamping Method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Clamping range: M1 - M16 Clamping shank: DIN ISO40 steep taper Length from spindle: 80mm < Tape clamping method: The taps are secured in the extension behind the square and the clamping shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo Extension extension - see photo Extensions and taps are not a part of the set! Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 4 / MK4 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Clamping range: M1 - M16 Clamping shank: BT ISO30 sharp cone Length from spindle: 80mm < br> Standard: JIS 6339 MAS ??BT 30 the attachments are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo (photo is for DIN69871) Extension extension - see photo (photo is for DIN69871) Extensions and taps are not part of the set! Function: The tap is clamped into a suitable TC312 collet which has a torque clutch already pre-set or possibly fine-tune it as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Clamping range: M1 - M16 Clamping shank: Straight cone BT ISO40 Length from spindle: 80mm < br> Standard: JIS 6339 MAS ??BT 40 the attachments are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Extensions are secured in the head via a bearing and stones - see photo (photo is for DIN69871) Extension extension - see photo (photo is for DIN69871) Extensions and taps are not part of the set! Function: The tap is clamped into a suitable TC312 collet which has a torque clutch already pre-set or possibly fine-tune it as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Adjustable Key for TC-312 and TC-820 Inserts Range: 7-40 mm Key Diameter Keys: 3,0mm For TC-312 Collet Pins Needed mildly good - inaccuracy from production. For TC-820, use is easy. Ref. : 3404-150

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 2 / MK2 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Screwdriver head for TC 312 for machine taps to DIN371 DIN374 and DIN376 This type (SF) is without length compensation! The torque clutch is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 3 / MK3 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Screwdriver head with length compensation for TC 312 for machine taps to DIN371 DIN374 and DIN376 Screw clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: 32mm, cylindrical < Clamping Shank Length: 70mm Tape Clamping Method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed. Screwdriver has a length compensation of approx. 0.5cm, so it is sufficient to programmatically adjust the cutting depth. The torque clutch eventually prevents the tilting of the tap.

Air Thread Cutter with Adjustable Arm Range: M3-M8 Speed: 630-700 rpm. / min. (clamping head VAT-SP08) Shoulder positioning: Rmin. 200mm, Rmax 1900mm Contains 6 pcs of TC-312 adapters with torque coupling for taps: DIN371: M3, M4, M5, M6, M8 DIN376: M6 , other adapters are possible buy - see related products. Contains air pressure regulator with separator and lubricator. Clamping cast iron plate not included! Angle head can be purchased for threading - see related products. Ref. No. 3404-425

Air Thread Cutter with Adjustable Arm Range: M3-M8 Speed: 630-700 rpm. / min. (clamping head VAT-SP08) Shoulder positioning: Rmin. 500mm, Rmax 1600mm Contains 6 pcs of TC-312 adapters with torque coupling for taps: DIN371: M3, M4, M5, M6, M8 DIN376: M6 , other adapters are possible buy - see related products. Contains air pressure regulator with separator and lubricator. Clamping cast iron plate not included! Angle head can be purchased for threading - see related products. Ref. No .: 3404-420

Air Thread Cutter with Adjustable Arm Range: M3-M8 Speed: 630-700 rpm. / min. (clamping head VAT-SP08) Shoulder positioning: Rmax 700mm Contains 6 pcs of TC-312 adapters with torque coupling for taps: DIN371: M3, M4, M5, M6, M8 DIN376: M6 , other adapters can be purchased - see related products. Contains air pressure regulator with separator and lubricator. Clamping cast iron plate not included! Ref. No. 3404-410

Air Thread Cutter with Adjustable Arm Range: M3-M8 Speed: 630-700 rpm. / min. (clamping head VAT-SP08) Shoulder positioning: Rmin. 200mm, Rmax 1400mm Contains 6 pcs of TC-312 adapters with torque coupling for taps: DIN371: M3, M4, M5, M6, M8 DIN376: M6 , other adapters are possible buy - see related products. Contains air pressure regulator with separator and lubricator. Clamping cast iron plate not included! Angle head can be purchased for threading - see related products. Ref. No. 3404-415

Quick-action tapping head with length compensation for TC 312 for machine taps according to DIN371 DIN374 and DIN376 Torque coupling is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 2 / MK2 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Quick-action tapping head with length compensation for TC 312 for machine taps according to DIN371 DIN374 and DIN376 Torque coupling is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 4 / MK4 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Quick-action tapping head with length compensation for TC 312 for machine taps according to DIN371 DIN374 and DIN376 Torque coupling is set directly on the collet. Clamping range: M1 - M16 (need to buy TC312 collet) Clamping shank: morse 3 / MK3 with carrier Clamping method: Taps are clamped into the TC312 clamps, which need to be purchased separately. The taps are secured in a collet by a square and a clamping shank. The tap is held firmly in the collet, pulling out after the clamping collar is depressed. The colts are secured in the head through the bearing and stones. It is also possible to buy threaded heads for taps made in accordance with JIS and ISO 529, which are not common to us. About 90% of the domestic market consists of taps made according to DIN371,374,376 TC312 clamping bits are not part of a thread cutter - they need to be purchased separately! < Function: The tap is clamped into a suitable TC312 collet which has a pre-set torque clutch or can be fine-tuned as needed.

Quick-action tapping head with length compensation for TC 312 attachments with torque coupling for machine taps Clamping range: M1 - M14 Clamping shank: HSK 63A Length from spindle: 65mm Standard: DIN 69893 - HSK-A63 Length compensation - see photo Method of clamping the tap: The taps are secured in the extension by a square and a clamping shank. The tap is firmly held in the extension, pulled out after pressing the clamping collar in the front of the extension. The attachments are secured in the head via the bearing and stones The attachments and taps are not part of the set! Functions: The tap is clamped in a suitable collet TC312, which has a torque coupling already preset, or it can be fine-tuned as needed. The thread cutter has a length compensation of approx. 0.5 cm, so it is enough to program the appropriate cutting depth. The torque coupling prevents the tap from twisting.