Drills for bent taps

Carbide drill for drilling bent taps For tap: M3 d1(H7): 2,5 mm Max. depth l3: 10mm Total length l1: 38mm Clamping shank: cylindrical 3 Helix angle: 0 ° C Use up to 65 HRC > Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0010

Carbide drill for drilling bent taps For tap: M4 d1(H7): 3,30 mm Max. depth l3: 14mm Total length l1: 46mm Clamping shank: cylindrical square Helix angle: 0 ° C Use for 65 HRC > Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0020

Carbide drill for drilling bent taps For tap: M5 d1(H7): 4,20 mm Max. depth l3: 19mm Total length l1: 50mm Clamping shank: cylindrical 5-edge Helix angle: 0A ‚ ° Use up to 65 HRC Speed â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0030

Carbide drill for drilling bent taps For tap: M6 d1(H7): 5,00 mm Max. depth l3: 23mm Total length l1: 50mm Clamping shank: cylindrical hexagon Helix angle: 0Â ° Use up to 65 HRC Speed(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application : NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. Ä. : 20.1860.0040

Carbide drill for drilling bent taps For tap: M8 d1(H7): 6.80 mm Max. depth l3: 23mm Total length l1: 60mm Clamping shank: cylindrical 8 edges Helix angle: 0A ‚ ° Use up to 65 HRC> Speed ??â €‹ â € ‹(for range M3-M12): 1000-1500 rpm rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0050

Carbide drill for drilling bent taps For tap: M10 d1(H7): 8.50 mm Max. depth l3: 25mm Total length l1: 80mm Clamping shank: cylindrical 10 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Working procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of use on NC and the centering on run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0060

Carbide drill for drilling bent taps For tap: M12 d1(H7): 10,20 mm Max. depth l3: 35mm Total length l1: 80mm Clamping shank: cylindrical 12 edges Helix angle: 0A ‚ ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines Manual machines with fixed guide < b> Procedure: The workpiece must be firmly fixed. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1860.0070

Carbide drill set for drilling bent taps For taps: M3 - M4 - M5 - M6 - M8 - M10 - M12 d1(H7): 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm Max. depth l3: 10/14/19/23/23/25/35 mm Total length l1: 38/46/50/50/60/80/80 mm Clamping shank: cylindrical Hexagon < br> Helix angle: 0  ° Use up to 65 HRC Speed ??â € ‹â €‹(for range M3-M12): 1000-1500 rpm Clamping: collet chuck or drill chuck Application: NC machines manual machines with fixed guide Working procedure: The workpiece must be securely fastened. 1. The axis of the drill and the drilled holes must match. 2. Carry out the centering precisely, in the case of application on the NC and the centering on the run use a lower speed. 3. Drill the bent tap - ideally dry, possibly with lubrication - when lubricating, be careful not to stick the chips! 4. Blow any chips left in the rain with a compressor or pull out with pliers / needle. 5. Use a new tap. 6. After cutting the thread, check the accuracy of the thread. Ord. A „. : 20.1865