Countersinking heads

Machine chuck for inner edges / machine needle Range: 3-41mm Bevel angle: 90 Â ° Number of runs: 1(run is rotating - ie for two uses) Clamping shank: morse 2 / MK2 The coaster is delivered without running â „c itu , these can be purchased with a sharp angle: a) 14 Â °(cat. No. 01-350), suitable for special bronze, plexiglass b) 20 Â °(cat. no. 01-358), suitable for ordinary steel, steel, plastics, stainless steel c) 25 Â °(cat. no. 01-359), suitable for aluminum, iron, sheets Needle dimensions: Total length: 165mm Front diameter Parts: 42mm Diameter of aluminum nuts: 65mm and 60mm Shank length: 78mm Blade insertion procedure and height adjustment deburring / chamfering 1) Loosen the worms on the body of the trimmer(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needler, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Run for machine needle 01-091 brand KOPAL. Shrink angle: 90 ° Podbrus blade: 14 ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Contact the Company: Kat. Ä. : 01-350

Run for machine needle 01-091 brand KOPAL. Shrinkage angle: 90 ° Podbrus blade: 20 ° Material: HSS Coating: uncoated Usage: suitable for Stainless steel, swords, plastics, stainless steel You can compare the differences in the undercut table in the attached photos. Contact the Company: Kat. Ä. : 01-358

Run for machine needle 01-091 brand KOPAL. Shrinkage angle: 90 ° Podbrus blade: 25 ° Material: HSS Coating: uncoated , Iron, Sheets You can compare the differences in the tablecloth in the attached photos. Contact the Company: Kat. Ä. : 01-359

Machine chuck for external edges / machine needle Range: 4-17mm Bevel angle: 90 ° Number of strokes : 1pc Clamping shank: cylindrical dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a ) 0Â °(kat. Ä. 02-304), suitable for brass, bronze, cast iron, heat-resistant steel b) 14Â °(cat. Ä. 02-300), suitable for special bronze, plexiglass c) 20Â °(cat. Ä. 02-302), suitable for ordinary steel, copper, plastics, stainless steel d) 20 ° TiN(cat. Ä. 2T300B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25Â °(kat. Ä. 02-306), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: 80mm Diameter Front parts: 18mm Diameter of aluminum nuts: 26mm Clamping shank length: 27mm Blade insertion procedure and adjustment needling / chamfering heights 1) Loosen both worms on the body of the needler and remove the aluminum and black nuts. Be careful that you do not lose the spring, it is free. 2) Put the body in the body, secure it with two worms and reassemble the whole needle. Tighten the worms on the body and loosen them by about a quarter to a half turn to maintain the function of the spring. 3) Adjust the height of the chamfer by tightening the aluminum nut - tightening = less chamfering, loosening = more chamfering. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and adjust it so that it runs out. 5) Always have a black versus mother attached to an aluminum mother.

Machine chuck for external edges / machine needle Range: 4-17mm Bevel angle: 90 Â ° Number of strokes: 1pc Clamping shank: MK1(morse 1) The heater is delivered without a run , these can be purchased with an angle blade: a) 0 Â °(cat. no. 02-304), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. no. No. 02-300), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-302), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T300B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â ° Â °(cat. no. 02-306), suitable for aluminum, iron, sheets Needle dimensions: Total length: 80mm Front diameter Parts: 18mm Diameter of aluminum nuts: 26mm Shank length: 27mm How to insert the blade and adjust the height of the needles / chamfering 1) Loosen both worms on the body of the drawbar and remove the aluminum and black nuts. Be careful that you do not lose the spring, it is free. 2) Insert the body into the body, secure it with two worms and reassemble the whole needle. Tighten the worms on the body and loosen them by about a quarter to a half turn to maintain the function of the spring. 3) Adjust the chamfer height by tightening the aluminum nut - tightening = less chamfering, loosening = more chamfering. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always have the black counter mother tightened to the aluminum mother.

Machine chisel for outer edges / machine needle Range: 4-17mm Bevel angle: 60A ‚Â ° Number of strokes: 1pc Clamping shank: cylindrical dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a) 0 Â °(cat. No. 02-303), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. No. 02-305), suitable for special Bronze, plexiglass c) 20 Â °(cat. No. 02-308), suitable for ordinary steel, copper, plastics, stainless steel and d) 20 Â ° TiN(cat. No. No. 2T305B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. No. 02-307), suitable for aluminum, iron, sheets Needle dimensions: Overall length: 80mm Front diameter: 18mm Diameter aluminum nut size : 26mm Shank length: 27mm Blade insertion procedure and edge / chamfer height adjustment 1) Loosen both worms on the body of the needle and remove the aluminum and black nuts. Be careful that you do not lose the spring, it is free. 2) Insert the body into the body, secure it with two worms and reassemble the whole needle. Tighten the worms on the body and loosen them by about a quarter to a half turn to maintain the function of the spring. 3) Adjust the chamfer height by tightening the aluminum nut - tightening = less chamfering, loosening = more chamfering. 4) Make sure that the runner is not drowned in the body of the needler, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always have the black counter mother tightened to the aluminum mother.

Machine chuck for external edges / machine needle Range: 4-17mm Bevel angle: 60 Â ° Â ° Number of strokes: 1pc Clamping shank: MK1(morse 1) blade: a) 0 Â °(cat. no. 02-303), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. no. No. 02-305), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-308), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T305B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â ° Â °(cat. no. 02-307), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: 80mm Diameter of the front Parts: 18mm Diameter of aluminum nuts: 26mm Shank length: 27mm How to insert the blade and adjust the height of the needles / chamfering 1) Loosen both worms on the body of the drawbar and remove the aluminum and black nuts. Be careful that you do not lose the spring, it is free. 2) Insert the body into the body, secure it with two worms and reassemble the whole needle. Tighten the worms on the body and loosen them by about a quarter to a half turn to maintain the function of the spring. 3) Adjust the chamfer height by tightening the aluminum nut - tightening = less chamfering, loosening = more chamfering. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always have the black counter mother tightened to the aluminum mother.

Machine chisel for external edges / machine needle Range: 4-37mm Bevel angle: 90 Number of slots for edge inserts : 2 Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: < br> a) 0 Â °(cat. no. 02-312), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Total length: 120mm Diameter of front part: 43mm Diameter of aluminum nuts: 65mm and 60mm Length of clamping shank: 38mm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chisel for external edges / machine needle Range: 4-37mm Bevel angle: 90 Number of slots for edge inserts : 2 Clamping shank: cylindrical dia. 16mm and dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a) 0 Â °(cat. No. 02-312), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. No. 02-310), suitable for special Bronze, plexiglass c) 20 Â °(cat. No. 02-313), suitable for ordinary steel, copper, plastics, stainless steel and d) 20 Â ° TiN(cat. No. No. 2T310B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. No. 02-314), suitable for aluminum, iron, sheets Needle dimensions: Overall length: 120mm Front diameter: 43mm Diameter aluminum nut dimensions : 65mm and 60mm Clamping shank length: 38mm Blade insertion procedure and edge / bevel height adjustment 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needler, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for outer edges / machine needle Range: 4-37mm Bevel angle: 60° Number of slots for edge inserts : 2 < br> Clamping shank: MK2(morse 2) The coaster supplies it n without bend , these can be purchased with a sharp angle: a) 0 Â °(cat. no. 02-317), suitable for brass, bronze, cast iron, Heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel d) 20 Â ° TiN(cat. no. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. no. 02-319), suitable for aluminum, iron, sheets Dimensions of the needle: Total length: 120mm Diameter of front part: 43mm Diameter of aluminum nuts: 65mm and 60mm Length of clamping shank: 38mm How to insert the blade and set the height of the needling / chamfering edges 1) Loosen the worms on the body of the pin(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needle, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Machine chuck for external edges / machine needle Range: 4-37mm Bevel angle: 60° Number of slots for edge inserts : 2 Clamping shank: cylindrical dia. 16mm and dia. 10mm The coaster is delivered without a run , these can be purchased with a sharp angle: a) 0 Â °(cat. No. 02-317), suitable for brass, bronze, cast iron, heat-resistant steel b) 14 Â °(cat. No. 02-315), suitable for special Bronze, plexiglass c) 20 Â °(cat. No. 02-318), suitable for ordinary steel, copper, plastics, stainless steel and d) 20 Â ° TiN(cat. No. No. 2T315B), suitable for ordinary steel, stainless steel, inconel, titanium e) 25 Â °(cat. No. 02-319), suitable for aluminum, iron, sheets Needle dimensions: Overall length: 120mm Front diameter: 43mm Diameter aluminum nut dimensions : 65mm and 60mm Clamping shank length: 38mm Blade insertion procedure and edge / bevel height adjustment 1) Loosen the worms on the body of the needler(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needler, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.