Countersinking and needling

Set of 6 countersinks HSSE TiN countersinks Material: HSSE - High-speed steel with cobalt admixture, TiN = titanium-nitride coating angles: 90 Â °(90 Â °) The set contains countersinks with diameters: 6,3mm(shank 5mm) 8,0mm(shank 6mm) 10, 0mm(shank 6mm) 12.0mm(shank 8mm) 16.0mm(shank 8mm) 20.0mm(shank 10mm) Sheet metal cassette

HSSE TiN Countersink HSSE Material: HSSE - Cobalt Stainless Steel, TiN = Titanium-Nitride Coating Angle: 90 ° (90st.) The set contains countersinks with diameters: 6,3mm (stopper 5mm) 8,3mm (stem 7mm) 10,4mm (stem 7mm) 12,4mm (stem 8mm) 16,5mm (stem 10mm) 20,5mm (10mm stopper) Plastic cassette

HSSE DIN335C Countersink HSSE Material: HSSE - Cobalt Admixture Steel Angle: 90 ° (90st. Stopper 4mm 5,0mm (Stopper 4mm) 6,0mm (Stopper 5mm) 6,3mm (Stopper 5mm) 7,0mm (Stopper 6mm) 8,0mm (Stopper 6mm) 8,3mm (stem 6mm) 10,0mm (stem 6mm 10,4mm (stem 6mm) 11,5mm (stem 8mm) 12,4mm (stem 8mm ) 15,0mm (10mm stem) 16,5mm (10mm stem) 19,0mm (stem 10mm) 20,5mm (stem 10mm) 23,0mm (stem 10mm ) 25,0mm (10mm stem) Plastic cassette

Set of countersinks with cylindrical shank and guide pin Application - for countersinking screws with cylindrical heads. Guide pin adapted to pre-drilled thread hole CSN 22 1604 / CSN 22 1604, DIN373 This set includes these countersinks (bolt - recess x pr guide pin): M3 - 6x2,5 M4 - 8x3,3 M5 - 10x4,2 M6 - 11x5 M8 - 15x6,8 M10 - 18x8,5

Set of countersinks with cylindrical shank and guide pin Application - for countersinking screws with cylindrical heads. Guide pin adapted to bolt hole Material: HSS ČSN 22 1604 / CSN 22 1604, DIN373 This set includes these countersinks (bolt - recess x pr. guide pin): M3 - 6x3,2 M4 - 8x4,3 M5 - 10x5,3 M6 - 11x6,4 M8 - 15x8,4 M10 - 18x10.5

Set of countersinks with cylindrical shank and guide pin Application - for countersinking screws with recessed head. Guide pin adapted to pre-drilled thread hole CSN 22 1605 / CSN 22 1605 This set includes these countersinks (screw - pin): M3 - 5,7x2,5 M4 - 7,8x3,3 M5 - 9,5x4,2 M6 - 11,4x5

Piston Puller Piston Diameter 54mm Puller Height: 38mm Screw M10 Expansion Plate Diameter: 11,5mm Pivot Diameter Diameter: 7,5mm

3p. conical bracket Number of blades: 3 Angle of blades: 90th. Maximum diameter: 7.8 mm Clamping shank 6mm Overall length: 50 mm Material: HSS - High-speed steel DIN335 C

Knife blade in case 541-090 The turning knife is only in the blade case. NOGA knives can not be used in this case, the blade can not be removed from the breech.

Machine chuck for inner edges / machine needle Range: 3-41mm Bevel angle: 90 Â ° Number of runs: 1(run is rotating - ie for two uses) Clamping shank: morse 2 / MK2 The coaster is delivered without running â „c itu , these can be purchased with a sharp angle: a) 14 Â °(cat. No. 01-350), suitable for special bronze, plexiglass b) 20 Â °(cat. no. 01-358), suitable for ordinary steel, steel, plastics, stainless steel c) 25 Â °(cat. no. 01-359), suitable for aluminum, iron, sheets Needle dimensions: Total length: 165mm Front diameter Parts: 42mm Diameter of aluminum nuts: 65mm and 60mm Shank length: 78mm Blade insertion procedure and height adjustment deburring / chamfering 1) Loosen the worms on the body of the trimmer(in the milled groove). 2) Insert the body into the body, secure it with two worms. 3) Adjust the chamfer height by tightening / loosening the aluminum nut. 4) Make sure that the runner is not drowned in the body of the needler, if so, rearrange the aluminum nut and check so that the runner protrudes. 5) Always tighten the aluminum nuts with the sprocket.

Run for machine needle 01-091 brand KOPAL. Shrink angle: 90 ° Podbrus blade: 14 ° Material: HSS Coating: uncoated Bronze, plexiglass You can compare the differences in the tablecloth in the attached photos. Contact the Company: Kat. Ä. : 01-350

Run for machine needle 01-091 brand KOPAL. Shrinkage angle: 90 ° Podbrus blade: 20 ° Material: HSS Coating: uncoated Usage: suitable for Stainless steel, swords, plastics, stainless steel You can compare the differences in the undercut table in the attached photos. Contact the Company: Kat. Ä. : 01-358