Collets and adapters

Special collet for clamping taps into a VTA reverse tap with torque coupling Clamping range of the collet: see label for individual variants Diameter and other dimensions: see label for individual variants To two collets fit each Vertex VTA thread cutter: VTA7-JT6 thread cutter: FC-10 (2.5-4.5mm) and FC-11 (4.5-6.5mm) collets Tap cutter VTA12-JT6 : collet FC-20 (4.0-7.0mm) and FC-21 (7.5-10.0mm) Tap cutter VTA20-M20 : collet FC-30 (8.0 -12.0mm) and FC-31 (14.0-19.0mm)

Quick release attachment / sleeve / insert / collet TC312 / GT12 with slip for machine taps The attachment clamps taps: DIN 371 (reinforced shank): see attached table DIN 376 (classic shank): see attached table Dimensions of the clamping part (insertion into the clamp - see 2nd photo) - the radius stones are 10mm wide, 4mm high and the wall thickness is 3mm. Method of clamping the tap: The taps are secured in the extension by a square and a clamping shank. The tap is firmly held in the extension, it is pulled out after pressing the clamping collar in the front of the extension. Features : The tap is clamped in a suitable collet TC312, which has a torque coupling already preset, or it can be fine-tuned as needed. This insert fits into a thread cutter - see related products. Cannot be used alone.

Quick release attachment / sleeve / insert / collet TC820 / GT20 with slip for machine taps The attachment clamps taps: DIN 371 (reinforced shank): see attached table DIN 376 (classic shank): see attached table Method of clamping the tap: The taps are secured in the extension by a square and a clamping shank. The tap is firmly held in the extension, it is pulled out after pressing the clamping collar in the front of the extension. Features : The tap is clamped in a suitable collet TC820, which has a torque coupling already preset, or it can be fine-tuned as needed. This insert fits into a thread cutter - see related products. Cannot be used alone.

Quick clamping attachment / sleeve / insert / collet TC1433 with slip for machine taps Attachment clamps taps: DIN 371 (reinforced shank): see attached table DIN 376 (classic shank): see attached table Tap clamping method: The taps are secured in the extension with a square and a clamping shank. The tap holds firmly in the bit, pulling out after pressing the clamping collar in the front of the bit. Features: The tap is clamped in a suitable TC1433 collet, which has a torque coupling already preset, or it can be fine-tuned as needed. This insert is clamped in the tap - see related products. Cannot be used alone.

Quick release attachment / sleeve / insert / collet for circular jaw / threaded eye The attachment clamps round jaws with an outer diameter: according to the selected variant Insert size: according to the selected variant Other dimensions - see product description for individual variants Dimensions of inserts: TC-312: radius stones are 10mm wide, 4mm high and wall thickness is 3mm. Outer / inner diameter of stones: 25.4mm / 19mm. TC-820: radius stones are 11mm wide, 5mm high and wall thickness is 4mm. Outer / inner diameter of stones: 39.5mm / 31mm. This insert fits into a thread cutter - see related products. We do not recommend using it alone.

Set of 8 quick-release bits / bushings / inserts / collets TC312 for machine taps The set contains the following bits for taps made according to DIN371: 1x M1(upne also M1,1 to M1,8) 1x M2(upne also M2,2 to M2,5) 1x M3 1x M3,5 1x M4 1x M5(upne also M4,5 and M6) 1x M8 1x M10 Inserts can also be purchased separately - see related products . How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The screw is clamped in a suitable collet TC312, which has a torque coupling already preset, or it is possible more fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.

Set of 8 quick-release bits / bushings / inserts / collets TC820 for machine taps The set contains the following bits for taps made according to DIN371: 1x M8 1x M10 1x M12 1x M14 1x M16 1x M18 1x M20 1x M22(upne also M24) < br> Inserts can also be purchased separately - see related products. How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The tap is clamped in a suitable collet TC820, which has a torque clutch already preset, or it is possible fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.

Set of 4 quick-release bits / bushings / inserts / collets TC820 for machine taps The set contains the following bits for taps made according to DIN371: 1x M5(clamps also M6) 1x M6(clamps also M5) 1x M8 1x M10 Inserts can also be purchased separately - see related products. How to clamp the tap: The taps are secured with four edges and a clamping shank in the attachment. The tap is held firmly in the attachment, pulled out after locking the clamping ring at the front of the attachment. Function: The tap is clamped in a suitable collet TC820, which has a torque clutch already preset, or it is possible fine tune as needed. This insert is fastened to the thread of the cut - see related products. Cannot be used alone.

Reducing insert for tapping machine with collets TC-820, after its use it is possible to clamp smaller collets TC-312 - see related products.

Reducing insert for thread cutter with collets TC-1433, after using which it is possible to clamp smaller collets TC-820 - see related products.

DIN 371 (reinforced shank) : M5 and also M6 DIN 376 (classic shank): M8 Thread clamping method: Taps they are secured behind the square and the shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.

DIN 371 (Standard Shank) M10 DIN 371 ( reinforced stopwatch): --- Length compensation - see enclosed photo Tape clamping method: The taps are secured in the extension behind a square and a clamping shank. The screwdriver holds firmly in the extension, pulling the clamping collar in the front of the extension. Function: The tap is clamped into a suitable TC312 collet that has a pre-set torque clutch or can be fine-tuned as needed. This insert is threaded - see related products. Can not be used alone.