Collet chucks and collets

Set of 18 pcs of ER 32 collets made of stainless steel on wooden board, ER32 collets Diameters: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20 mm Pliers can be clamped: - Up to 2.5 mm diameter 0.5 mm - From 3 mm diameter 1.0 mm Accuracy : 0,005mm Material: INOX / stainless steel Standard: DIN 6499B / 470ESP Collet clamping procedure: Snap the collet into the clamping nut - according to the attached picture .

ER40 ER40 , 19, 20, 22, 26, 30 mm Collet clamping procedure: Screw the clamp into the clamping nut - according to the attached picture.

Set of 21 collets ER 40 on a wooden board, collets ER40 Diameters: 3 , 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13 , 14 , 15 , 16 , 17 , 18 . 0.015mm Standard: DIN 6499B / 470E Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture.

Set of 24 sealed collets ER 40 for use with tools with internal cooling, collets ER40 Diameters: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 , 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26 mm Collet clamping procedure: Snap the collet into the clamping nut - according to the attached picture. standards Standard: DIN6499C / 472EA Max. pressure tested by the manufacturer: 40bar Tools with internal cooling are not produced with a shank smaller than 3mm, so this set starts from a diameter of 3mm.

Simple cutting jig for ER25 collets with square shank / clamping For ER25 collets(outer diameter 25mm) Max. size of collet that goes into this chuck: 16mm ER25 collets can be purchased separately - see related products Clamping shank: square 35mm Length of clamping part: 42mm Total length of clamp: 68mm Clamping nut diameter: 42mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 18.5mm Application: For square milling / grinding.

Simple cutting jig for ER32 collets with square shank / clamping For ER32 collets(outer diameter 32mm) Max. size of collet that goes into this chuck: 20mm ER32 collets can be purchased separately - see related products Clamping shank: square 40mm Length of clamping part: 42mm Total length of clamp: 70mm Clamping nut diameter: 50mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 24mm Application: For square milling / grinding.

Simple cutting jig for ER40 collets with square shank / clamping For ER40 collets(outer diameter 40mm) Max. size of collet that goes into this chuck: 30mm ER40 collets can be purchased separately - see related products Clamping shank: square 44.5mm Clamping part length: 48mm Total length clamps: 80mm Clamping nut diameter: 63mm The nut has 6 notches(-socket wrench - see related products) The clamp is through: dia. 28mm Application: For square milling / grinding.

ER11 collet holder with cylindrical shank 16mm, L=150mm Collet holder, collet head for NC - ER 11, cylindrical shank with weldon surface Clamping range of ER11 clamp: 1.0 - 7.0mm Diameter of the clamping shank: 16 mm Length of the clamping part: 100mm Total length of the clamp: 120mm Diameter of the through hole: 7.9mm Diameter of clamping nut: hexagon 19mm Nut thread: M14x0.75 Throwability: up to 0.005mm Balance: G2.5 / 20,000 rpm ER11 collets (outer diameter 11mm) can be purchased separately - see related products Procedure for clamping the collet: Snap the collet into the clamping nut - according to the attached picture. Usage : Clamping of drills, cutters and other tools with a cylindrical shank As a tap without length compensation and reversal - for clamping taps Clamping possible in a collet and in a weldon clamp.